grow lights controller

The Gavita Master EL2 controller has two outputs for optional External Contact Modules (ECM).

An external contactor module, ECM1, has been developed for EL2 controllers. Because the main controller operates on a low-voltage output, it is unable to switch additional equipment. With the ECM1, you can extend the functionality of your EL2 controller to switch auxiliary equipment such as heaters, dehumidifiers and CO2 equipment during lights on or lights off, according to the lighting hours set by the controller.

These contactor devices can switch a load of up to 15 amps while turning the lights on or off. Because ECMs are controlled by a low voltage signal, you can even place them close to the appliances themselves, allowing for easy installation and optimal flexibility. Extremely easy installation - plug and play.

• Never guess again whether a contactor is on or off: the ECM's LED clearly shows the state of the contactor.
• Mount it right next to the equipment you want to control and simply plug the control wire (safe, low voltage) into the ECM and the controller .

Technical data:

• ECM voltage 120-240V
• ECM current 15A AC3
• ECM Switch Type DPST (Double Pole)
• ECM AC terminals Male and female plug (depending on market and voltage), 40 cm / 1 ”4” cables
• ECM Control Input Low Voltage Cage Clamps
• ECM Indicator blue LED

Gavita Master controller EL2

Maximum control, ease of use, safety and easy installation. Simply connect the controller cables to your module using the included T-splitter, set the modules to EXT (external control), connect the module and controller to the mains and you are ready to use your lighting system.

The controller can turn on and off all modules connected to it (Model EL2 can control two separate rooms with up to 40 ballasts in each, or just one with up to 80 ballasts), can adjust the desired level of light emitted by the modules (percentage or as absolute value) and even mimics sunrise and sunset, by gradually starting and stopping the lamps when they are turned on and off.

Master controller are able to control the lights to simulate sun rise and sunset.

You can customize the operating time as you want. It provides the excellent care for your indoor growing environment

- 2 MODES:  master controller has "follow mode" and "inverse mode". Follow mode requires to put only one sensors close to rooms' climate control system so that both sensors are exposed to the same temperature. Inverse mode requires to use both sensors in different room, so 2 sensors will execute inverse action, you can choose to control the lights in which room.

-CLEAR INTERFACE: master controller contains multiple functions with simple button control. Clear digital screen can accuratly indicate your settings, status and controller menu.

-SAFETY CONTROL master controller is designed with 2 quality sensors for checking temperature in all time.You can set your desired temperature so that it will automatically dim the lights when the temperature reach a specific level and turn off the lights if it reaches another temperature. "Main" and "aux" jacks each can be connected up to 80 ballasts (160 as total).

CONTROL ALL OF YOUR LIGHTS WITH ONE CONTROL UNIT WITH ADDED HEATING CONTROL (3PHASE)

The Advanced GSE Control Unit is a professional indoor growing timer & contactor system for turning on 4 x 600w lights.

ABOUT THIS CONTROL UNIT FOR INDOOR CULTIVATION

• This system is  will turn on 4 x 600w lights in groups of 2 with a 25 second delay between each group. 
• The benefit of this is that you do not have a large start up power surge by turning all the lights on at once. 
• This model includes a heating socket which turns on when lights are off (power management).

The timer box GSE 8x600W supplies current 4x16A to relays for ballasts 8x600W + heating

The Timer Box III is built from high-quality components. The Timer box controls several inductive loads. One of them is high pressure lamps. The timer in the dashboard is German - Grasslin , and the contacts are Slovenian - ISKRA . The case is hermetically sealed and secured, which provides it with protection class IP54.

You can open or close the circuit with a circuit breaker. The contactor is based on the control system and is designed for up to 4x600W inductive load. The heating socket is only activated when the lamps are switched off.

Technical data:

• Size: 500x160x115mm
• Voltage: AC 230V/400V 50-60 Hz
• Power: 7200W fully loaded (32A)
• Heating: up to 2400w (resistive loads)
• Mechanical timer: 24h automatic/manual
• Setting interval: 15 minutes
• Mechanical durability of relays: 10,000,000 cycles
• Protection class: IP54

TIMER BOX II DELAYS THE LIGHTING AND HEATING (3 PHASE)

The GSE Control Unit (Timer Box III) is a professional indoor growing timer & contactor system for turning on 6 x 600w lights.

ABOUT THIS CONTROL UNIT FOR INDOOR CULTIVATION

The timer box is used by several inductive loads such as high-pressure lamps with high switch on and off simultaneously. This turns on Contactor/Relay 4x600W loads.Model with heating socket is on when lights are off (power management)

Gavita Master controller EL1

 
Lighting control at your fingertips!

Using a Gavita Master controller to control your e-series fixtures offers you maximum control, ease of use, plug and play installation and safety. Just connect the controller cables to the fixtures with the included T-splitter (see diagram), set the dials on the fixtures to EXT (External control), plug the controller and the fixtures directly into mains and you are set to go.

The controller can switch all the interconnected fixtures on and off with its internal timer, adjust them to your required output level (in percentage or exact output power) and even simulate sunrise and sunset to gradually adjust the climate in your grow room when your lights go on or off. This electronic controller replaces expensive lighting timers and contactors while preventing ballast current in-rush when switching on your lights.

Two very important features are the autodim function and emergency shut-down. When the temperature in your grow room rises beyond the control level of your climate control your crop can be damaged beyond recovery. The temperature probe senses this and will automatically dim the lights to not overshoot your safe temperature, and maintain it. The display and warning LED indicate when this happens, and also indicate if this has happened while you were away so you can correct the problem. If for any reason your climate control completely fails and the temperature rises to unacceptable levels the system will perform an emergency shutdown of all connected equipment. The alarm contact of the controller can be connected to your alarm system for instant notification.

You can connect all your e-series fixtures to one controller.
 

It regulates the speed of lights from 0 to 300W.

The lights in our growing place can be connected to the power regulator reducing or increasing the lights' strenght.

Specifications:

- Cornwall Electronics
- Power regulator
- LED power indicator
- Voltage: 230V
- Frequency: 50Hz / 1.6A
- 0-300W

Boxing relay switches two independent circuits - stopped them and release them.

It is operated by a third power cord that must be plugged into a timer switch or GSE timer box. Each of electricity networks can withstand 4x600W (total svetlinie 8x600W).

Sizes and technical data's:

• Case: WxHxD = 180x130x60mm
• Timer box: WxHxD = 160x100x90mm
• Volt: 2x230V / 50Hz
• Relays: 4x16A 230V
• Protection class: IP54

TIMER BOX II DELAYS THE LIGHTING AND HEATING

The GSE Control Unit (Timer Box II) is a professional indoor growing timer & contactor system for turning on 6 x 600w lights.

ABOUT THIS CONTROL UNIT FOR INDOOR CULTIVATION

The timer box is used by several inductive loads such as high-pressure lamps with high switch on and off simultaneously. This turns on Contactor/Relay 4x600W loads.Model with heating socket is on when lights are off (power management)

This relay box for indoor growing switches two indipendent power circuits on and off.

It's controlled by a third power cord which needs to be plugged to a commercial timer or a GSE timer box.

Each power circuit can handle 4x600W (total 9x600W lights).

YOU CAN MANAGE UP TO 8 GROW LIGHTS AT THE SAME TIME

This relay box for indoor growing switches two indipendent power circuits on and off. It's controlled by a third power cord which needs to be plugged to a commercial timer or a GSE timer box.

Each power circuit can handle 4x600W (total 8x600W lights).

SIZES AND TECHNICAL DATA:

• Case = 180x130x60mm
• Timer box: WxHxD = 160x100x90mm
• Volt: 2x230V / 50Hz
• Relays: 4x16A 230V
• Protection class: IP44

A CONTROL UNIT FOR INDOOR GROWING CAN MANAGE UP TO 6X600W LAMPS

The Advanced GSE Control Unit for grow box manage the indoor lighting of plants, is a professional timer & contactor system for turning on 6 x 600w lights.

FEATURES OF THIS CONTROL UNIT FOR GROW ROOM:

• This system will turn on 6 x 600w lights in groups of 2 with a 25 second delay between each group. 
• The benefit of this is that you do not have a large start up power surge by turning all the lights on at once. 
• This model includes a heating socket which turns on when lights are off (power management)

TIMER BOX II DELAYS THE LIGHTING AND HEATING

The GSE Control Unit (Timer Box II) is a professional indoor growing timer & contactor system for turning on 6 x 600w lights.

ABOUT THIS CONTROL UNIT FOR INDOOR CULTIVATION

The timer box is used by several inductive loads such as high-pressure lamps with high switch on and off simultaneously. This turns on Contactor/Relay 4x600W loads.Model with heating socket is on when lights are off (power management)

YOU CAN MANAGE UP TO 8 GROW LIGHTS AT THE SAME TIME

This relay box for indoor growing switches two indipendent power circuits on and off. It's controlled by a third power cord which needs to be plugged to a commercial timer or a GSE timer box.

Each power circuit can handle 4x600W 

SIZES AND TECHNICAL DATA:

• Case: WxHxD = 180X130X60MM
• Timer box: WxHxD = 160x100x90mm
• Volt: 2x230V / 50Hz
• Relays: 4x16A 230V
• Protection class: IP44

A CONTROL UNIT FOR INDOOR GROWING CAN MANAGE UP TO 6X600W LAMPS

The Advanced GSE Control Unit for grow box manage the indoor lighting of plants, is a professional timer & contactor system for turning on 6 x 600w lights.

FEATURES OF THIS CONTROL UNIT FOR GROW ROOM

• This system will turn on 6 x 600w lights in groups of 2 with a 25 second delay between each group. 
• The benefit of this is that you do not have a large start up power surge by turning all the lights on at once. 
• This model includes a heating socket which turns on when lights are off (power management).

CONTROL ALL OF YOUR LIGHTS WITH ONE CONTROL UNIT WITH ADDED HEATING CONTROL

The Advanced GSE Control Unit is a professional indoor growing timer & contactor system for turning on 4 x 600w lights.

ABOUT THIS CONTROL UNIT FOR INDOOR CULTIVATION

• This system is  will turn on 4 x 600w lights in groups of 2 with a 25 second delay between each group. 
• The benefit of this is that you do not have a large start up power surge by turning all the lights on at once. 
• This model includes a heating socket which turns on when lights are off (power management).

The Advanced Control Unit is a professional timer & contactor system for turning on 4 x 600w lights.

• This system will turn on 4 x 600w lights in groups of 2 with a 25 second delay between each group. 
• The benefit of this is that you do not have a large start up power surge by turning all the lights on at once. 
• This is relevant as a light typically requires about 20% extra ampage to 'start up' as opposed to when they are up and running.