Milwaukee

The light is necessary for the development of the plants.

In fact, it is necessary a sufficient contribution of light in order to favor the photosynthesis and the closing of the plants. The supplement of light by means of lamps electrical workers is the method simpler and economic in order to bring the necessary light to the plants.

MW700 is a portable Lux meter designed to perform light measurements. It is supplied with a light sensor connected to the meter that measures from 0 to 50000 Lux. Average indoor lighting ranges from 100 to 1000 Lux and average outdoor sun lights about 50000 Lux. Lux is a unit that indicates the density of light that falls on a surface.

The MW700-WP is a portable Lux meter designed to perform light measurements. The instrument is supplied in a hard carrying case complete with a light sensor connected to the meter that measures from 0 to 50000 Lux. The light sensor is waterproof, suitable to verify the light intensity also at the bottom of your aquarium. The accuracy is ±6% of reading (full scale). The MW700-WP works with a 9V alkaline battery. Automatic shut-off after 10 minutes saves battery and extends Lux meter life.

 20 ml pH 7.01

 

-liquid pH 7.01 to calibrate electronic pH meters

-content: 20ml

- calibration-table on the packaging

Milwaukee C65 / C66 is a waterproof EC tester, specially designed for hydroponics and agricultural markets, with automatic temperature compensation and manual calibration with 1 point.

The EC tester has a range of 0.00 to 10.00 mS / cm as well as an optional electrode option and is supplied in a battery pack, calibration solution (M10031) and a calibration screwdriver. The modular design allows easy replacement of the electrode and batteries.

Specifications:

• range: from 00 to 10.00 mS / cm
• resolution: 0.01 mS / cm
• accuracy: ± 2%;
• Calibration: automatic, single point
• automatic temperature compensation with β = 2% / ° C
• Operating conditions: -5 to 50 ° C / 32 to 122 ° F ;, humidity up to 100%
• batteries: 3 x 1.5V (included)
• Battery life: approx. 250 hours of continuous use
• dimensions: 165 x 30 x 30 mm

CALIBRATION:

• Frequent calibration is recommended for maximum measurement accuracy.
• Immerse the tester electrode in a glass of tap water
• Immerse the probe in a suitable calibration solution: 1413 mS / cm.
• Open the top cover of the tester and, using the screwdriver included in the kit, turn until 1.41 appears on the display.

PH buffer solution  4,01 20 ml

- pH-4.01 buffer solution for calibration of electronic pH meters

- content: 20ml

- calibration-table on the packaging

Milwaukee's economical testers are easy-to-use and low cost instruments to measure quick and reliable pH, EC or TDS values.

Measuring electrical conductivity is the best way of checking the amount of salt or dissolved solids (TDS) in water. Milwaukee provides you with a range of pocket testers that will allow you to measure from very low to very high conductivity solutions. All EC/TDS testers compensate for the temperature variance automatically.

The CD611 is a Conductivity tester specifically designed for water analysis. The calibration procedure is very simple and fast. This tester has automatic temperature compensation, 100 µS/cm resolution and a range of 0 to 20000 µS/cm. CD611 is supplied complete with protective cap, calibration screwdriver, batteries and instructions.

Accurate, easy to use and reliable. 24/7 EC monitoring

The Milwaukee MC310 PRO Conductivity (EC) Monitor allows you to automatically measure EC levels and alerts you with an alarm when you are out of set point range.

The MC310 EC automatically monitors your EC levels. Simply set your EC parameters and let the Milwaukee EC Monitor do the rest.
It is often used in nutrient tanks, hydroponics and gardening.
The Milwaukee PRO EC monitor offers:
ACCURACY
The Milwaukee PRO EC monitor offers accuracy up to ±2% of full scale.
AUTOMATION
The monitor has a set point range of 1.0 to 5.0 mS/cm with alarms that activate when readings are above or below the set point.

EC buffer solution 20 ml 1.413

- solution EC  1,413 for the calibration of electronic meters EC

-content: 20ml

- calibration table on the packaging

• The Milwaukee MW100 PRO pH meter features manual calibration and fast operation in a rugged design.
• The Milwaukee MW100 PRO pH meter is ideal for pools and hydroponics.
• The MW100 provides fast results to ±0.2 pH accuracy with two-point manual calibration.

Professional pH-monitor for long-term use

The devices of the MS series are designed for constant monitoring of pH, EC or TDS values, directly in the tank. Each unit has a mode selection that is set by the user. The LED indicator activates and starts flashing when the pH, EC or TDS level changes above or below (user selected) the set value.

The pH-monitor for constant monitoring of hydroponic or fertilizer solutions , aquariums and aquaponic systems, pools, etc. has a convenient function for visual indication when the pH of the solution passes a set (by the grower) value (up or down, as selected by a knob).

• Manual calibration at 2 fixed points - pH 4 and pH 7.
• Separately connectable sensor compatible with pH monitors of other manufacturers.
• LED alarm
• Supplied with 12 VDC adapter, mounting kit and 20ml pH 7.01 calibration solution
• Dual, cruciform pH electrode with two meter cable (BNC connector)

Manufacturer's warranty - 2 years for the device, 6 months for the sensor. Does not apply to mechanical damage and improper operation!