Magnetic ballasts
In magnetic ballasts, current flows through coils of copper wire before moving on to the light bulb. Most of the current gets caught in the magnetic field it generates, with only small increments moving on to the light bulb. The current that is passed on depends on the thickness and the length of the copper coil. This inconsistent flow of the current is what causes the lights of the lamp to flicker and also creates the buzzing sound.
Tomax 250W Magnetic Ballast
Ballast with a rated power of 250 W. Appropriate for High Pressure Sodium and Metal Halide bulbs.
Quality Lighting Ballast
This ballast allows the stabilization of the current supplied in output at the same time guarantees a greater stability of the luminous flux and consequently a greater duration of the lamps. Closed body for further isolation and safety, It is wired easily thanks to the screw terminals on the front.
Suitable for the lighting of bulbs HPS and MH 250W.
Tomax 400W Magnetic Ballast
Ballast With a Rated Power of 400 W. Appropriate for High Pressure Sodium and Metal Halide bulbs.
Quality Lighting Ballast
This ballast allows the stabilization of the current supplied in output at the same time guarantees a greater stability of the luminous flux and consequently a greater duration of the lamps. Closed body for further isolation and safety, It is wired easily thanks to the screw terminals on the front.
Suitable for the lighting of bulbs HPS and MH 400W.
magnetic ballast Tomax 600W
Electromagnetic start-regulating device for sodium and metal halide lamps
This ballast allows the stabilization of the current supplied to the output while guaranteeing a greater stability of the light flow and therefore a longer duration of the lamps. Closed body type for further insulation and safety.
Tomax 600W open ballast - magnetic
Ballast with a rated power of 600 W. Appropriate for High Pressure Sodium and Metal Halide bulbs.
Quality Lighting Ballast
This ballast allows the stabilization of the current supplied in output at the same time guarantees a greater stability of the luminous flux and consequently a greater duration of the lamps. Open body.
Suitable for the lighting of bulbs HPS and MH 600W.
- output is 600w or more
- works with both HPs and MH lamps
- Easily mountable
- Long strike distance to the lamp up to 15m
- thermal cutouts to protect against short circuits
- pre-wired input and output cable
- CE certified
- 18months warranty
MST 600W ballast
MST 600W is an electromagnetic start-regulating device for sodium and metal halide lamps
It consists of a choke, a starter ("lighter"), a capacitor and a control circuit.
- Warranty: 1 year from date of sale
- 230V, 50Hz; λ>0.9; starting voltage 5KV;
- Cable to lamp <20m (HPS), <2m (MH);
- Protection class IP 20;
Chokes (ballasts) adjust the voltage supplied to the selected lamp, up to the working one for it and ignite the lamp by creating a high voltage pulse after the interruption of the current from the starter. Magnetic chokes are compact and cost-effective devices that are suitable for "lighting" lamps from 250W to 1000W. It is recommended that chokes be kept outside of smaller grow rooms, as they convert some of the electricity they absorb into heat and can thus contribute to an increase in temperature.
Magnetic ballast solux 250W
Ballast with a rated power of 250 W. Appropriate for High Pressure Sodium and Metal Halide bulbs.
Quality Lighting Ballast
- Solux ballasts are suitable for both sodium and metal halide lamps.
- They incorporate a thermal protection chip. They offer a high efficiency, long duration, comfortable and uniform light based on the reduction of the loss of power and the increase of the luminous efficiency. The lamps start without flashes and provide a stable and quite silent light.
magnetic ballast solux 400W
Ballast with a rated power of 400 W. Appropriate for High Pressure Sodium and Metal Halide bulbs.
Quality Lighting Ballast
- Solux ballasts are suitable for both sodium and metal halide lamps.
- The position called "Super Lumens" increases the power by 10% (440w) with which it squeezes the bulb beyond 100%.
- They incorporate a thermal protection chip. They offer a high efficiency, long duration, comfortable and uniform light based on the reduction of the loss of power and the increase of the luminous efficiency. The lamps start without flashes and provide a stable and quite silent light.
Solux magnetic 1000W ballast
1000W ballast for lighting HPS and MH lamps
High quality 1000 w ballast in Class II. Made in Italy, robust and completely safe, which complies with European legal regulations and tested in accordance with: EN61347-1-2-9, EN60923, EN55015 among others. Very simple connection through the scheme shown. The lamp can be connected at a maximum distance of 16 meters.
- Power (W): 1000
- Output Voltage (V): 230
- Amperage: 10.3А
- Dimensions (mm): 213x176x360
Master Gear 600W ballast
Electromagnetic ballast for HPS and MH lamps.
Master Gear suitable for coupling with sodium or metal halide lamps with power 600W. The maximum possible distance from the lamp to the throttle is 20 meters for HPS and 5 meters for MH lamps. MASTER GEAR 600W consists of inductors, capacitor and terminal block for connecting input voltage and lamp. 6,2A.
EuroGear Pro ballast 400W
The EuroGear Pro ballast closes the gap between cheap low-quality ballasts and expensive high-end products
Among IP 54 and CE certifications the EuroGear Pro is equipped with a thermal protection to eliminate potential danger of fire. Additionally after production every single ballast is being checked for full operability, so that a safe continuos operation is guaranteed.
The EuroGear Pro is fully cabled.
Specifications
- Compact electromagnetic ballast with thermal protection
- 100% EU
- for HPS and HPI-type lamps
- IP 54 and CE certified
- Excellent cost-benefit ratio
- Splashproof enclosure
- 230V/ 50Hz
- Power cable length: 1.5 m
- Lamp cable length: 3.55 m
EuroGear Pro ballast 600W
The EuroGear Pro ballast closes the gap between cheap low-quality ballasts and expensive high-end products.
Among IP 54 and CE certifications the EuroGear Pro is equipped with a thermal protection to eliminate potential danger of fire. Additionally after production every single ballast is being checked for full operability, so that a safe continuos operation is guaranteed. The EuroGear Pro is fully cabled.
Specifications
- Compact electromagnetic ballast with thermal protection
- 100% EU
- for HPS and HPI-type lamps
- IP 54 and CE certified
- Excellent cost-benefit ratio
- Splashproof enclosure
- 230V/ 50Hz
- Power cable length: 1.5 m
- Lamp cable length: 3.55 m
magnetic ballast Sinowell 600W
Ballast with a rated power of 600 W. Appropriate for High Pressure Sodium and Metal Halide bulbs.
Quality Lighting Ballast
This ballast allows the stabilization of the current supplied in output at the same time guarantees a greater stability of the luminous flux and consequently a greater duration of the lamps. Closed body for further isolation and safety, It is wired easily thanks to the screw terminals on the front.
Suitable for the lighting of bulbs HPS and MH 600W.
ballast ETI 250W
Ballast with a rated power of 250 W. Appropriate for High Pressure Sodium and Metal Halide bulbs.
Quality Lighting Ballast
ETI Magnetic Ballast 250w has been designed for HPS and MH AGRO lamps. Power supplies (o ballast) ETI UAL series are defined “Hybrid” as it equipped with an electronic circuit which integrates the functions lighter and capacitor. The latest models of this series have been improved and adapted to the ignition of all gas discharge lamps. The compact body and wiring in the absence of external leads, make this product particularly suitable for application in the grow room.
This ballast allows the stabilization of the current supplied in output at the same time guarantees a greater stability of the luminous flux and consequently a greater duration of the lamps. The ignition systems ETI have closed for further isolation and safety, It is wired easily thanks to the screw terminals on the front.
Suitable for the lighting of bulbs HPS and MH 250W.
ballast Mari 600W
600W ballast for lighting HPS and MH lamps
Specifications:
- CE approved ballast
- Running quiet and high efficient
- With no top housing design for beter cool
ballast Mari 1000W
1000W ballast for lighting HPS and MH lamps
Specifications:
- CE approved ballast
- Running quiet and high efficient
- With no top housing design for beter cool
GIB 600W ballast
GIB Ballast PRO-V-T 600W with Thermal Fuse
PRO-V-T ballast without internal cable connections, built-in thermostat for automatic over-heating, silent thanks to the anti-vibration base.
- Silent and low vibration due to its anti-vibration base
- Thermal fuse: Excludes the possibility of overheating
- Intelligent shutdown
- Device with a linear fuse
- By standards meeting the requirements for European certification (CE) and European electrical certification standards (ENEC)
- With an explosion-proof capacitor
