Lighting

The color emitted by these lamps is very distributed throughout the spectrum.

It contains some colors of the spectrum that are not found in mercury lamps, so halogenides are more suitable for the growth of plants, emitting a blue / white light. Within the halide lamps used in indoor gardening, the most used are the SUNMASTER due to the development, branching, dry weight, production, etc. that is achieved with them. 600W bulb.

• Wattage: 600W
• Mains Voltage (V): 400V
• Rated Hours: 6000
• CCT (K): 4500 K
• Luminous Flux (lm): 50 000
• Bulb Screw: E40

Metal halides have the more balanced spectrum.

The light they give out has a significant amount of light from the bluer end of the spectrum, which the plant uses to grow vegetatively. It produces plants with a small internodal length, with large leaves and thick stems. It produces the most natural looking plants. It simulates the light from the beginning of the year and is good for plants before they're switched into flowering mode.

They're normally slightly more expensive than HPS. Recently, there have been 'enhanced spectrum' MH bulbs produced which also give off a significant amount of red light. Conversion bulbs are also available which plug into HPS ballasts which are actually MH bulbs. Useful for changing the light balance without changing the ballasts also. In the event of a power failure, they need about 20 minutes before restating. They may restart earlier but it shortens the life of the bulb quite dramatically to try and start a hot bulb.

• Power Plant HIT/HBU/LU Metal Halide Lamp - 1000 watt.
• Power Plant Metal Halide lamps promote optimum vegetative growth and flowering.
• Provides a richer more nutritious light
• Compatible with standard HPS ballasts and ignitor systems. Lamps can simply be changed to maximise growth protential.400w hps = 38,000 lumens

Power Plant HIT/HBU/LU Metal Halide Lamp - 600 watt.

• Power Plant Metal Halide lamps promote optimum vegetative growth and flowering.
• Provides a richer more nutritious light
• Compatible with standard HPS ballasts and ignitor systems. Lamps can simply be changed to maximise growth protential.

We recommend that lamps are replaced every 12 to 14 months, after 14 months there is an appreciable drop in the lumen output leading to a reduction in crop yield 


600w hps = 51,000 lumens
 

Power Plant HIT/HBU/LU Metal Halide Lamp - 1000 watt.

• Power Plant Metal Halide lamps promote optimum vegetative growth and flowering.
• Provides a richer more nutritious light
• Compatible with standard HPS ballasts and ignitor systems. Lamps can simply be changed to maximise growth protential.

We recommend that lamps are replaced every 12 to 14 months, after 14 months there is an appreciable drop in the lumen output leading to a reduction in crop yield 


1000w hps = 100,000 lumens

Sunmaster Finishing Deluxe Lamps​​​​​​​

Improves aromas and flavours. Helps ripen fruit and increases oil production.For use in the last 10 days of flowering.
​​​​​Sunmaster Finishing Deluxe lamps are the best in the violet-blue end of the spectrum and give off the perfect light for the final stages in the growth cycle.

Ultraviolet radiation is quite important in biological photochemical reactions as well as in the elimination of certain mildews.  Engineered in Ohio and utilizing specialty chemicals optimized in Illinois, Sunmaster’s FINISH product family delivers the perfect light spectrum for the final stage of a plants’ growth cycle.Partner with Sunmaster ‘COOL’ and ‘SUPER’ to maximize yield.

• Initial Lumens (Lumens @ 100 hours) 50000
• PAR Watts 174
• Rated Life (Hrs. @10Hr. /Start) 10000
• Correlated Colour Temperature K 10000
• Chromaticity (CIE - X,Y) 338 351
• Colour Rendering Index (CRI) 65
• Typical Warm Up Time (Minutes) 3-5
• Typical Hot Restart Time (Minutes) 5-10
• Burning Position Universal

Benefits

• Strong UV violet-blue component for the final stage in the plant growth cycle
• Improves aroma and flavors
• Long life and high output 10K
• Features
• Exclusive Venture Lighting lamp chemistry
• Strong output, weighted in the blue/violet/UV end of the spectrum
• E-ballast compatible

The Philips SON-T PIA model is an ideal option for the flowering period of your plants

These lamps contribute to better absorption of CO2 , to better and better photosynthesis and growth. Son-T Pia lamps emit the highest amount of light per unit watt (PAR). It is the most efficient lamp with the best technical performance and the lowest energy consumption. It is switched on by means of a choke/ballast, placed 50-60 cm from the top of the plants.

• socket E40;
• specially optimized for flowering;
• real power: 603W ;
• current through the lamp: 5.8A;
• voltage: 110V;
• light output: 86,500Lm;
• life: 20000 hours;
• color temperature: 2000K;

The growth, fruiting, hardiness and even flowering time of plants are completely dependent on the light they receive. The quality and intensity of the light, as well as the duration of lighting are extremely important! Building the right lighting system would guarantee you excellent results.
HPS lamps emit red light that helps increase production in the flowering phase.

PHILIPS SON T PRO 1000W

• Cost-effective and reliable high presion
• Bulbo sodium transparent outer tubular
• High luminous efficacy Robust construction shock and vibration resistant lamp
• regulable
• Alumbrado roads and residential areas

Compatible with both electronic and magnetic ballasts!

• These bulbs have both Blue spectum (Growth Stage) and Red Spectrum (Flowering Stage)– a better growing for you plants!
• Optimized spectrum: Dual spectrum and high PAR (Photosynthetic Active Radiation) to promote healthy plant growth in vegetative or flowering stages;
• Long lifetime: Lifetime as long as 24,000 hours, maintaining over 90% of initial lumen (140000LM) output after running for 5,000 hours;
• Wide application range: with more energy in yellow and red spectrum to enhance flowering, these horticultural high pressure sodium lamps can be used in all stages of plant growing;
• Lumens: 90 000lm
• CRI: 22Ra

Compatible with both electronic and magnetic ballasts!

• These bulbs have both Blue spectum (Growth Stage) and Red Spectrum (Flowering Stage)– a better growing for you plants!
• Optimized spectrum: Dual spectrum and high PAR (Photosynthetic Active Radiation) to promote healthy plant growth in vegetative or flowering stages;
• Long lifetime: Lifetime as long as 24,000 hours, maintaining over 90% of initial lumen (140000LM) output after running for 5,000 hours;
• Wide application range: with more energy in yellow and red spectrum to enhance flowering, these horticultural high pressure sodium lamps can be used in all stages of plant growing;
• Lumens: 130 000lm
• CRI: 22Ra

A 250W lamp suitable for both growing and flowering stages.

Stimulates photosyntesis due to the emitted blue light.

Range features

• Patented arc tube delivers highest photosynthetic efficiency of any lamp in the world
• Performance maintained at an exceptional level due to improved structure of outer bulb
• Optimised for the highest Phytolumens or PAR output
• GroLux light spectrum maximises red output essential for plant growth
• Industry leading lumen maintenance of 95% at the end of life
• Suitable for a plethora of applications related to plant growth

OSRAM PLANTASTAR ® is designed to meet the needs of gardeners quality of a light source, particularly radiating in the range suitable for growing plants in two phases - growth and flowering.

The lighting in greenhouses can not be compared for example with that on the road due to the difference between the manner in which plants perceive light and the perception of light by the human eye. With the advent of sodium lamps PLANTASTAR ® market, Osram provides a light source that meets all requirements of good lighting for growing rasteniya.

Low maintenance costs very constant luminous flux during the first 20,000 hours of operation, optimized design with a patented shock absorber NEW reinforced ceramics resistant sodium guaranteeing long life laser welding ensures precise geometrical relationship and constant high quality due to optimized manufacturing process are part of the characteristics of this lamp !

After a period of 20 thousand servant. hours or every two years is recommended to replace the lamps.

Technical data:

• Power: 1000W
• Socket: E40
• Luminous flux: 130000 lm
• Color temperature: 2000K
• Electricity: 10.6A
• Energy cinsumption: 1056kW/1000h

DATA SHEET

Lumii Black 600w Hps Lamp

Greenhouse lighting cannot be compared to, for example, roads, due to the difference between the way plants perceive light and the perception of light by the human eye. LUMii black HPS is a combined 600W dual spectrum sodium lamp and E40 socket. Perfect for stimulating enhanced flowering and powerful growth!

For best results, we recommend using them with LUMii or LUMii BLACK Ballast

• Power: 600W
• Base: E40
• Luminous flux: 88 000lm
• Life: 20,000 hours
• Phase: growth and flowering
• Spectrum: Combined / Dual

The growth, fruit, endurance and even flowering time of plants are completely dependent on the light they receive. The quality and intensity of light, as well as the duration of lighting are extremely important! Building the right lighting system would guarantee you excellent results. Combined lamps emit both red and blue light, making them a suitable light source for both the flowering phase and and for the growth phase.

At different times in the growing cycle, plants require different types of light radiation. 

Immature plants have different needs to those about to mature. To maximise the potential of a plant, to ensure that it grows strong and healthy, you need to deliver just he right kind of light radiation it needs – when it needs it.

The NEW Sunmaster Dual Spectrum lamp is a radically new, scientifically developed lamp designed for the commercial and hobby grower. Using the new Dual Spectrum lamps – which are fully compatible with your existing fittings and ballasts – you can deliver improved blue and red light to your plants at the crucial stages in their development. And it's so simple to do.

Techinacal data:

- Produces higher chlorophyll level for greener healthier plants
- Promotes larger leaf area/mass
- Inhibits unnatural stem elongation
- Encourages increased number of internodes while maintaining compact plant
- Produces thicker primary stems
- Offsets the blue deficiencies of HPS
- Encourages earlier flowering and total number of flowers
- Supports accelerated linear growth
- Increases total number of branches as well as internodes
- Delivers higher fruit weight
- Produces higher yields (total biomass)
 

Set Reflector + Ballast

The hottest energy efficient HID lighting technology in a ready kit! Ceramic Metal Halide , or CMH for short (some call it CDM), is becoming increasingly popular in the horticultural industry. CMH lamps have a very broad light spectrum that is closer to the sun itself than any other form of HID lamp . CMH lamps also have an increased AR/Watt efficiency compared to other forms of HID lighting . The CMH fixture can be used as a main light; main light for SOG applications; or supplemental full-spectrum light for large crops.

Set Reflector + Ballast + Lamp for flowering

The hottest energy efficient HID lighting technology in a ready kit! Ceramic Metal Halide , or CMH for short (some call it CDM), is becoming increasingly popular in the horticultural industry. CMH lamps have a very wide light spectrum that is closer to the sun itself than any other form of HID lamp . CMH lamps also have an increased AR/Watt efficiency compared to other forms of HID lighting . The CMH fixture can be used as a main light; main light for SOG applications; or supplemental full-spectrum light for large crops. The CMH 315 horizontal mounting location of a single lamp ensures an even distribution of light.

The hottest technology in energy efficient HID lighting is now available!

Ceramic Metal Halide, or CMH for short (some call it CDM), is becoming increasingly popular in the horticultural industry. CMH lamps have a very broad light spectrum that is closer to the sun itself than any other form of HID lamp. CMH lamps also have an increased AR/Watt efficiency compared to other forms of HID lighting. The CMH fixture can be used as a main light; main light for SOG applications; or supplemental full-spectrum light for large crops.

*LAMP IS NOT INCLUDED IN THE KIT

Effective lighting in professional greenhouses!

The GreenPower lamp is optimized in a broad spectrum with a peak in the 660nm DeepRed area
The peak in the 660nm DeepRed area makes the plant more generative which results in a stronger bloom of the plant in the flowering stage

Growth, fruit, endurance, and even the flowering time of plants are completely dependent on the light they get. The quality and intensity of light as well as the duration of illumination are extremely important! The construction of the appropriate lighting system will guarantee you excellent results. The combined lamps emit both red and blue light, making them a suitable light source for both the blooming phase and for the growth phase.

Effective lighting in professional greenhouses!

Each 315 watts lamp produces light equivalent to 500-600 watts of traditional MH / HPS light. Since these lamps spend less than 350 watts of power, it means you can save up to 40% of your power bill while covering the same area. Most manufacturers that use CMH lighting get higher yields and a big leap in quality.

• Ceramic metal halide lamp for growth
• Spectral distribution optimized for photosynthesis efficiency
• Blue Spectrum for Healthy Plant Growth and Strength
• Ceramic μmol output within the PAR spectrum (Photosyntesis Active Radiation)
• Economically profitable (long average life, high PMI output, low energy consumption)
• Easy lamp change

Growth, fruit, endurance, and even the flowering time of plants are completely dependent on the light they get. The quality and intensity of light as well as the duration of illumination are extremely important! The construction of the appropriate lighting system will guarantee you excellent results. The combined lamps emit both red and blue light, making them a suitable light source for both the blooming phase and for the growth phase.

Effective lighting in professional greenhouses!

Each 315 watt lamp produces light equivalent to 500-600 watts of traditional MH / HPS light. As these lamps use less than 350 watts of power , this means you can save up to 40% on your power bill while covering the same area. Most growers who use CMH lighting get higher yields and a big jump in quality.

CMH lamps are very good at growth and flowering, especially those with a warmer color spectrum (around 3000K), but no better than HPS in the red spectrum area.

• Ceramic metal-halide grow lamp
• Spectral distribution optimized for photosynthetic efficiency
• Blue spectrum for abundant plant growth and strength, red spectrum for flowering.
• Ceramic μmol output within the PAR spectral region (Photosynthesis Active Radiation)
• Economical (long half-life, high μmol production, low energy consumption)
• Easy lamp replacement

Specifications:

• Light output (lights per 100 hours) 32000lm
• Lumens per watt: 100lm/W
• Estimated life (hour per 10 hours / start) 15000h
• Color temperature (K): 3100K
• Color rendering index (CRI) or (Ra) > 95
• Typical reboot time (minutes) 6-8min
• Position: BU + 90º

The growth, fruiting, hardiness and even flowering time of plants are completely dependent on the light they receive. The quality and intensity of the light as well as the duration of illumination are extremely important! Building the right lighting system would guarantee you excellent results. Combination lamps emit both red and blue light, making them a suitable light source for both the flowering phase and and for the growth phase.

A useful accessory , designed specifically to protect the eyes from excessive light and to neutralize the spectral shift caused by sodium lamps.

Because of the strength of the light and its specific spectrum, it is often difficult to notice the early symptoms of fertilizer deficiency or the appearance of parasites. These glasses filter orange light by converting the HPS-spectrum into a spectrum close to the eye's natural one. So you can observe the true colors of your plants - leaves, fruits and flowers.

Safety glasses are a necessary accessory for those times when you want to observe your plants in their light period without harming your eyes.

Protective case for growroom glasses

Thanks to the protective glasses, the growers can observe their plants indoors without the strong light hindering their eyes. Keeping this accessory is just as important! That durable case will help you when you do not use your glasses.

• black color
• length: 16cm

GSE electronic ballast can manage all kind of MH metal highlight and HPS high pressure sodium bulbs at 250-400-600W.

A UV- acid- and waterproof foil build in LED indicate the status and on 3knobs you can change the wattage. By steps from 660W-600W-400W-250W or with push and hold even step less from 660W to 250W. GSE uses only finest high quality components such as aluminium casted long live and high temperature electrolytic capacitor, transistors PhilipsNXP, high frequency ISKRA components etc... and source >84% EU manufactured components.

A extremely big-surface aluminium radiator keeps the running temperature low and provides a long life of the components. The high frequecy above 80kHz to 220kHz avoids acustic resonance of the bulb. The ballast comes as a finish assembled product with 3m connector cable and 4m lamp cable to connect to the reflector E40. It is all waterproof sealed and have IP64 protection class.
 

Lumii Black 600w Digital Ballast 250w-660w

This 600w Electronic Ballast is supplied as a stand-alone ballast with a flying IEC lead so you can add any reflector fitted with an IEC socket to start growing. The ballast features both dim and boost functions, having the ability to control the light output from the lamp.

​​​​​​​The ballast features both dim and boost functions, having the ability to control the light output from the lamp. There are two dimmable options (250w & 400w) and a ‘super-lumens’ boost option (600w+Boost) which is on average an extra 10% increase in output. 
For best results, always use the correct lamp per wattage setting

More light output per watt of energy consumed

Electronic throttle with microprocessor control!

Lumatek digital ballasts offer the most advanced technology on the market for greenhouse lighting. Compact and completely silent, they have the highest efficiency - more lumens per watt than any other model. Microprocessor technology allows adjustment to the lamp model used and its condition, as well as to the mains voltage.

WHAT ARE THE ADVANTAGES OF HIGHER LIGHT EMISSION?
More light with less energy consumption and hence, greater productivity on the same surface. By using a suitable reflector, the increased light can be distributed over a larger surface.

​

Digital Ballast Lumatek provides the most advanced technology on the market for greenhouse lighting. 

Compact and completely silent, it has the highest efficiency - more lumens per watt than any other model. Microprocessor technology allows adjustment to the model's lamp and its condition as well as to network's voltage. Lumatek Twin 600W 240 V is adjustable, electronic ballast for use with one or two 600W and / or 400W 240V HPS and MH lamps  for plants.

Why Digital Ballasts?

• More Lumen Output - Up to 20% more lumens output than some old style magnetic ballasts ...More light equals more yield. We urge you to test this yourself with a good quality light meter. Be sure to also check how much power the ballast is using with an ammeter as many so called 600w magnetic ballasts now draw up to 750w as standard to try to keep up with Lumatek’s lumen output.
• Stable Light Output - Excellent for Pharmaceutical-agriculture, laboratories and other uses where precise regularized output is essential.
• Fast Start-up - It reaches full brightness in under one minute; magnetic ballasts typically take about twenty minutes.
• Completely Silent - No noise or vibration of any kind
• Produce Less Heat - Less heat generated by the ballasts allows cooler running of the environment. Less heat is less wasted electricity.
• Longer Bulb Life - Lumen output loss over time, with the correct lamp, is dramatically less than with magnetic ballasts.

LUMATEK 1000W AC DIGITAL BALLAST FEATURES: 

• Runs 400W, 600W and 1,000 MH or HPS lamps
• Fully Dimmable
• Staggered Ignition Technology (will light multiple bulbs in a sequence)
• Super Lumens feature for 1000+ watt operation
• Whisper quiet fan and lightweight
• Dual-Voltage with the same light output on 120V or 240V @ 50/60 Hz
• Input Power: 1030w, Ouput Power: 1000w
• Power Factor: >0.99
• Voltage Range: 108 to 264v
• THD: <8%
• Environment Temperatures: -25 to 50 C (-13 to 122 F)
• FCC compliant, ETL listed

Electromagnetic start-regulating device for sodium and metal halide lamps

This ballast allows the stabilization of the current supplied to the output while guaranteeing a greater stability of the light flow and therefore a longer duration of the lamps. Closed body type for further insulation and safety.

Suitable for lighting HPS and MH 600W bulbs.

• Power of 600w or more
• Works with both HPS and MH lamps
• Easy to install
• Long distance to connect to the lamp, up to 15m
• Thermal switches for short circuit protection
• Pre-wired input and power cable
• CE certified

1000W ballast for lighting HPS and MH lamps

High quality 1000 w ballast in Class II. Made in Italy, robust and completely safe, which complies with European legal regulations and tested in accordance with: EN61347-1-2-9, EN60923, EN55015 among others. Very simple connection through the scheme shown. The lamp can be connected at a maximum distance of 16 meters.

• Power (W): 1000
• Output Voltage (V): 230
• Amperage: 10.3А
• Dimensions (mm): 213x176x360

MST 600W is an electromagnetic start-regulating device for sodium and metal halide lamps

It consists of a choke, a starter ("lighter"), a capacitor and a control circuit.

• Warranty: 1 year from date of sale
• 230V, 50Hz; λ>0.9; starting voltage 5KV;
• Cable to lamp <20m (HPS), <2m (MH);
• Protection class IP 20;

Chokes (ballasts) adjust the voltage supplied to the selected lamp, up to the working one for it and ignite the lamp by creating a high voltage pulse after the interruption of the current from the starter. Magnetic chokes are compact and cost-effective devices that are suitable for "lighting" lamps from 250W to 1000W. It is recommended that chokes be kept outside of smaller grow rooms, as they convert some of the electricity they absorb into heat and can thus contribute to an increase in temperature.

SUNRail allows you to illuminate a larger area more efficiently.

SunRail is a system of lightweight, adjustable and self-propelled rails that carry a lighting system (or several) along a 1.90 meter long aluminum rail and can cover an effective illuminated area of 1.20 x 3.50 meters. SunRail can support up to 3 devices simultaneously thanks to the high resistance of the aluminum and the high-performance motor that drives the system.

This system is ideal for use with an Adjust a wings reflector to increase light projection.

Using the "spreader", which reduces the heat emitted by the lamp, the reflector can be lowered 20cm above the tops of the plants. It can also be installed under the lamp to be able to get as close as possible to the tops of the plants, without the risk of burning. The light is diffused and reflected to the reflector for more even illumination. Suitable for 1000W lamps.

Using the "spreader", which reduces the heat emitted by the lamp, the reflector can be lowered 20cm above the tops of the plants. It can also be installed under the lamp to be able to get as close as possible to the tops of the plants, without the risk of burning. The light is diffused and reflected to the reflector for more even illumination. Suitable for lamps from 400W to 600W.

Moves the lighting back and forth along a 220cm long rail.

In this way, it can be placed closer to the plants , as it does not stay in one place for long. Increases lamp efficiency and life.

Features:

• Travel speed - 3-3.30 minutes in one direction
• Movement pause from 2 to 120 seconds.
• Adjust the movement speed
• Possibility to limit the lifting by means of clamps.
• Holds up to 10 kg
• Drive motor power: 12W

Reflector complete with two CFL 2x55W lamps.

Suitable for germination as well as the vegetation phase.

Gloria reflector with cooling Ф150mm

This reflector gives your garden the light it needs, without unnecessary heat.

Features:

• Wide spread of light allows plants to be spaced close together for maximum light in low light areas
• Made of heavy-duty, pre-galvanized steel
• The fully sealed glass ensures a snug fit
• Made from precision 95% reflective European aluminum
• Comes with built-in socket, 5m power cable and hanging hooks
• Reflector size: 50CM x 70CM x 20CM

SPUDNIK is an ideal aircool reflector, providing lamp cooling by allowing the hot air around the lamp to be drawn out of the room before it has a chance to create high heat.

SPUDNIK has been the choice of professionals for years, with an extremely efficient reflector: 97% reflectivity!

• 97% reflectivity
• Miro9 - internal reflector
• Includes 4mm thick glass sheet
• Flange - 125mm (5") or 150mm (6")

The reflector is suitable for 400W and 600W lamps.

• Attach a small fan and it will blow the hot air out of the lamp.
• In this way, the temperature of the lamp will be reduced by up to 30-40%.
• The lamp can be moved closer to the tops of the plants.
• Perfect for rooms where several lamps are connected.
• Diameter Ø 125 mm
• LENGTH 300 mm

Adjust-A-Wings is a high-class reflector equipped with Super Spreader for even higher efficiency.

Manufactured from the highest quality materials, this reflector brings a number of benefits to both plants and gardeners.

• Twice the power and efficiency of most other reflectors on the world market;
• Increase the cultivation area, with each lamp, by up to 75%;
• Increases lamp performance up to 50%;
• Reduces heat, saves energy;
• Corrosion resistant;
• 97% Reflection;
• Super Alloy glass coating;
• Adjustable double, parabolic reflectors.
• Dimensions - 70cm x 55cm

Defender is a model created for the more professionally oriented growers.

It has all the qualities of the Enforcer model, but unlike it combines a combination of high-class technologies, aesthetics, strength, efficiency and easy installation. The main difference is that the Defender is made from extremely strong aluminum (H18), used in aircraft construction, which is extremely strong and extremely flexible.

This allows preserving the perfect parabolic curves, so important in light dispersion, otherwise vulnerable to changes when mounting and dismounting the reflector. In addition, the surface is covered with a titanium-white, heat-resistant polymer coating reducing the heat emitted by the lamp and having the property of spreading the light extremely evenly and having a reflectivity of 86% .

Hobby version of the popular Avenger!

The shape of this reflector gives the same even light distribution and reflection as the Avenger, but is made from a lower grade aluminum and does not include the Super-Spreader.
The Enforcer has the same benefits as the Avenger, including an impressively low-hanging position over your plants and balanced light distribution.

The reflection is around 86% and is guaranteed to maintain its reflection for a minimum of 3 years

• Economical double parabolic reflector
• Control "hot spots" by attaching a "Super-Spreader"

Effect of Adjust A Wings ENFORCER:

• Twice as powerful and efficient as most other reflectors on the world market
• Increases grow area per lamp by up to 75%
• Increases lamp performance by up to 50%. Reduces heat and saves energy

Pearl pro is a relief reflector developed by Adjust A wings that offers a more powerful light reflection (+ 5.1%) compared to a standard Stucco reflector.

With the same power consumption, it provides greater radiation over the area of interest. Pearl Pro will give you a higher yield! The same with more powerful light sources. Significantly better light distribution (+ 10%) compared to conventional mirror Stucco reflectors helps to reduce the number of hot spots and uniform light distribution.

Thanks to better light distribution and intensity, Pearl Pro gives you better coverage. Accordingly, crop uniformity will be better. Up to 60% more lumens compared to Stuсco!

• Use with ballast corresponding to lamp power - 1000W maximum
• New junction box design keeps moisture away from electrical connections
• Mounting metal plate supporting the weight of the lamp
• Secure connection method

This reflector is characterized by its absolute stability.

This reflector has not only the advantages of its predecessors, but also acquired several new functionalities during its development.

The reflector can not only be adjusted in height, but can also be tilted and positioned according to your needs. Thanks to the middle reflector, maximum reflectivity is achieved. Therefore, the light is spread so evenly that the appearance of hot spots is almost zero and the use of an additional diffuser becomes unnecessary. Another novelty is the upper rail, which allows the reflector to be installed not only symmetrically, but also flexibly. No spreader needed - AZERWING does not have a spreader, this should provide better light dispersion compared to previous models.

Meanwhile, it turned out that the spreader can lead to concentrated shading and form a Doppler effect (that is, when more Adjust-A-Wings are mounted in parallel with spreaders, there is a danger of light overlap). In addition, it is not necessary to maintain a wide angle in places where several reflectors meet; on the other hand, it has a sharp angle that guarantees a homogeneous specific output without any hot spots.

Reflector wings have a finely forged structure – just like the Adjust-A-Wing. Prima Klima uses a new material for its reflectors – VEGA GREEN PVD coating, which reflects an optimized radiation background for plants.

• Adjustable socket
• No hotspot
• Guaranteed reflectivity up to 95%
• L/W/H 55 x 58-72 x 20 cm

Adjust-A-Wings is a high-end reflector equipped with a Super Spreader for even higher efficiency.

Manufactured from the highest quality materials, this reflector brings a number of benefits to both plants and gardeners. Designed for maximum efficiency, the Avenger model is made with a coating of fused glass and titanium dioxide, using PVD (Physical vapor deposition). technology - the most advanced technique for laying reflective surface layers on a number of work surfaces. This coating is the most reflective, most durable and sustainable coating known to science.

• Twice the power and efficiency of most other reflectors on the world market;
• Increase the cultivation area, with each lamp, by up to 75%;
• Increases lamp performance up to 50%;
• Reduces heat, saves energy;
• Corrosion resistant;
• 97% Reflection;
• Super Alloy glass coating;
• Adjustable double, parabolic reflectors.
• Dimensions: 100cm x 70cm
• Suitable for: 1000W or 2x400W, 2x600W sodium (HPS) or metal halide (MH) lamps
• Illuminated area: Up to 3.89 m2.